Friday, September 19, 2014

Bearing Press System

The Bearing Press System installs the following sizes: 6000, & 6900, (10mm ID); 6001, 6801, & 6901 (12mm ID); 1526, 6002, 6802, & 6902 (15mm ID); 6003, 6803, & 6903 (17mm ID); 6804, & 6904 (20mm ID); 2437 (24mm ID); 6805 (25mm ID); 6806 (30mm ID).

The Bearing Press Handles are machined from 6061-T651 Aluminum billet to exacting tolerances then anodized to decrease wear. Ergonomic handles to ensure consistent bearing pressure while reducing hand fatigue. The 3/8-12 ACME rod is 9 inches in length.


SPECIFICATIONS:

•Anodized and Laser Etched for part identification.

•Adapter’s pilot on the Bearing ID and pushes on the Bearing OD to prevent damage during installation.

•Ergonomic Handle ensures consistent bearing pressure while reducing hand fatigue.

•Includes standoffs for frame linkage.


Thursday, August 15, 2013

Press Fit 30 & BB30 Bottom Bracket Press Adapters


BB30 Bottom Bracket Installation Adapter Tool - Red

Designed to install BB30 bearings in the frames bottom bracket shell. Includes two Press Adapters which are used in conjunction with a Park HHP-2 bearing cup press to press bearing into the frame.

BB30 Press Adapters

Park HHP-2 w/BB30 Adapters


Press Fit 30 Bottom Bracket Press Adapters - Black

Set includes two Press Adapters which can be used in conjunction with Park HHP-2 bearing cup press. Installs BB90, BB92, Shimano Press Fit, SRAM Press Fit GXP, Race Face Press Fit and other press fit BB systems.
PF30 Press Adapters
Park HHP-2 w/PF30 Adapter
If you do not own a Park HHP 2 Press or other brand press, I can offer these press adapters with a threaded rod press as shown in the below pictures.

BB30 Press Adapter Tool
PF30 Press Adapter Tool

Chris King Press Fit 24 & 30 Bottom Bracket Installation Adapters



Chris King PF30 Adapters
These Press Adapters are machined from 6061-T651 Aluminum billet to exacting tolerances then anodized to decrease wear.

The PF30 Adapters are designed specifically to install Chris King Press Fit 30 Bottom Brackets and 1-1/4” Headsets by properly applying pressure across the top of the bearing cup assembly which eliminates bearing damage during installation.

Chris King PF24 Adapters
The PF24 Adapters are designed specifically to install Chris King Press Fit 24 Bottom Brackets and 1” Headsets by properly applying pressure across the top of the bearing cup assembly which eliminates bearing damage during installation.

The Adapters are compatible with the Park Headset Press (HHP-1,2,3), Pedros Headset press and Woodman.

Thursday, February 7, 2013

Fork Wiper & Oil Seal Installation Tool

The Fork Wiper & Oil Seal Installation Tools are designed to work with Rock Shox, Fox and Enduro Seal Kits. The installation tool has both a dedicated wiper seal side and oil seal side to ensure proper installation without damaging seals or casting.


• 32mm Tool – Anodized Army Green
• 34mm Tool – Anodized Blue
• 35mm Tool – Anodized Black
• 36mm Tool – Anodized Red
• 40mm Tool – Anodized Clear

The Fork Wiper & Oil Seal Installation Tools are machined from 6061-T6 Aluminum to exacting tolerances then anodized to decrease wear.

Tuesday, September 13, 2011

Tapered Fork - Crown Race Setter Tool

Tool Setup w/CRS-1


Section View

This Tapered Fork Crown Race Setter Tool is designed to be used in conjunction with the Park CRS-1 Driver Tube to install the headset crown race onto the fork's crown seat.   This tool is designed only to work with forks that have tapered steer tubes.

The Tapered Fork Crown Race Setter is machined from 6061-T651 Aluminum to exacting tolerances then anodized to decrease wear.

Headset Press Adapter[s] for 1 1/2 inch and Tapered Chris King Headsets


1-1/2 Headset Press Adapters

Tapered Headset Press Adapters

The Headset Press Adapter[s] are for - 1 1/2 inch and Tapered Chris King Headsets.

These Adapters are machined from 6061-T651 Aluminum billet to exacting tolerances then anodized to decrease wear.These Adapters are designed specifically to install Chris King 1 1/2 and Tapered Headsets by properly applying pressure across the top of the bearing cup assembly which eliminates bearing damage during installation.

The Adapters are compatible with the Park Headset Press (HHP-1,2,3), Pedros Headset press and Woodman.The Race Adapter is to be used when installing the base plate on the fork steer tube. The beveled side of the Race Adapter goes against the base plate before using a crown race setting tool.


Note: Frame preparation should be done in accordance to Headset Manufacture.

Wednesday, June 30, 2010

1/2" DU Bushing Tool & RWC Needle Bearing Tool

1/2" Bushing Tool w/RWC Needle Bearing Drift
This Tool is designed to remove & replace shock eyelet bushings. DU bushings are a press fit into the shock eyelets so this tool can be used in a vise, arbor press or with a soft headed hammer. Here is an illustration of the tools use http://forums.mtbr.com/showthread.php?t=396483 The RWC Needle Bearing Ejector Pin installs and removes the Needle Bearing Kit sold by Real World Cycles.


The 1/2" DU Bushing Tool and RWC Tool are machined from Stainless Steel to exacting tolerances to reduce tool wear. The 1/2" Bushing Tool will Fit shocks from Fox, Cane Creek, Romic, Marzocchi Roco, 5th Element Coil, and Rock Shox (Monarch and Vivid). The RWC Needle Bearing Ejector Pin will only fit the Real World Cycling Needle Bearing Kit.